Home » knowledge » Poor Quality Products from China: What to Do Before Shipping or Reordering

Poor Quality Products from China: What to Do Before Shipping or Reordering

2026-11-16 00:00:00

Decide whether the failed lot can supply a verified quantity

When products from a Chinese supplier fail inspection, base the recovery shipment on identifiable goods that passed suitable checks. Decide whether sorting can establish an acceptable quantity before promising stock to customers. A supplier's estimate of how many units are probably good is not enough for that allocation.

This guide addresses recovery from the affected lot. Start with the purchase order, approved specification revision, inspection report and lot identity. Keep affected stock distinguishable, preserving original labels and photographs. Rework, replacement or credit may address the commercial loss, but purchasing still needs to know which goods are available.

Use the responsibilities below as a recommended working arrangement. Assign the roles before sorting begins, including a quality approver and the party responsible for shipment instructions.

Check whether sorting can answer the problem

NIST describes full inspection of rejected lots and replacement of defective units as a common procedure when sampling and testing are nondestructive. Its rectifying-inspection explanation supports considering a complete screen after rejection; it does not establish that a particular screen detects every relevant failure.

The buyer's quality lead should specify the characteristic, requirement, test method and result needed to classify each unit. A visible label mismatch may permit direct screening. Appearance cannot establish material or performance compliance. Obtain the inspector's agreement that the proposed method addresses the observed defect before purchasing approves the sorting scope.

NIST lists destructive testing among the circumstances in which acceptance sampling is used. Its acceptance-sampling guidance explains this exception to checking every saleable unit. Where the necessary test destroys the product, the quality lead should obtain a technical specialist's proposed test method, sampling basis and acceptance criteria for the designated quality approver. Keep the quantity unresolved until that assessment supports a disposition.

Reconcile the sample with the remaining stock

Account for the original sample before commissioning another screen. Were sampled units returned, retained, consumed or segregated? State whether the sorting instruction includes them. Count units as acceptable only when the required checks are complete and their identity is preserved.

Hypothetical example: a 1,000-unit lot undergoes a nondestructive 80-unit sample inspection. Six units fail and 74 pass. Screening the remaining 920 units finds 114 failures and 806 acceptable units. Assume both groups receive the same required checks and remain identifiable:

Stock groupAcceptable unitsRejected unitsTotal
Original sample, counted once74680
Remaining stock screened806114920
Reconciled lot8801201,000

If all 880 acceptable units remain available, the gap against a 1,000-unit requirement is 120. Adding the six sampled failures again would incorrectly produce 126. Missing units belong in an unresolved balance, not automatically in either the accepted or rejected column.

Price the recovery against the quantity it delivers

Request a sorting quotation that specifies the units covered, checks included, segregation and repacking. In the hypothetical example, $0.40 for each of the remaining 920 units produces a $368 bill. Allocating that charge across all 880 acceptable units gives approximately $0.42 per acceptable unit.

This is an incremental sorting-cost allocation. It excludes the original purchase, earlier inspection, replacements, additional verification, storage and transport. The earlier inspection has already happened; do not count it again as new sorting expenditure.

Compare proposals at the same required quantity and date. Shipping 880 units now leaves a 120-unit gap. Purchasing should establish whether the partial quantity serves demand and when verified replacements could be ready. Logistics can then price separate movements against holding accepted stock for a combined shipment.

Assign the exceptions before arranging pickup

Use one exception register with the affected quantity, package identities, evidence, owner and next decision. The following procedure keeps a discrepancy from disappearing between the factory, inspector and booking contact.

Trigger and responsible roleAction and evidenceDecision and unresolved outcome
The quality lead finds that the screen cannot resolve the defect.Obtain a specialist's method and acceptance basis, linked to the specification and inspection finding.The designated quality approver decides acceptability; otherwise, keep affected units unresolved.
The warehouse lead finds a count or identity mismatch.Recount affected packages and reconcile sample status, sorting results and package identifiers.The quality approver reviews the corrected balance; exclude unaccounted units from the proposed pickup.
Purchasing finds the accepted quantity below demand.Document the required quantity and date, replacement readiness and transport alternatives.The buyer's designated purchasing approver chooses partial delivery or waiting; replacements remain outside the accepted balance pending checks.
The logistics coordinator finds a changed package list or no acknowledgment.Send the corrected list, location and readiness date to the assigned movement authority and handlers.That authority issues revised instructions; escalate missing acknowledgment and obtain a confirmed collection plan.

Quality acceptance and cargo movement require separate authorization. The quality approver assesses the goods; the party assigned movement authority under the booking or contract instructs collection, holding or release. An inspection report alone confers neither authority. If ownership is unclear, purchasing should identify the responsible party before logistics treats collection as confirmed.

For Forestleopard's sea freight service or air freight service, provide the accepted carton or pallet list, quantities, location and readiness date. Identify rejected stock remaining at the factory and replacements following separately. Request costs for that configuration. If packages are opened, mixed or repacked, reconcile their contents and identifiers before using the revised list.

Keep recovered stock separate from reorder confidence

ASQ explains that sampling identifies defects but does not tell you where or when they occur in the process. Its sampling guidance distinguishes detection from finding and fixing causes. Recovering acceptable stock therefore does not demonstrate that the production failure has been corrected.

Before reordering, have the quality lead connect the defect to a proposed process correction and checks on the next lot. Keep recovered units, repairs awaiting verification and future replacements separate. A screen supports only the characteristics adequately checked; safety-sensitive goods or unresolved technical failures need appropriate specialist assessment before acceptance for use or sale.

Ask Us
Please read the Q&A, and if you cannot find your answer, send us your question and we will answer you as soon as possible.

Your Name (*)

Your Email (*)

Subject

Department

Your question

Copyright © 2025 ForestLeopard. All Rights Reserved.湘ICP备2024098933号-2 - 服务信息